Analogue Control (9)

This is a drive unit for the FineTrack series electric point N. Features Easy connection with connector system Can be replaced by sliding to the side even after the rail is fixed Two are used for double cross points Ultra-thin, 3mm thick Cord length: 120cm

The Kato Standard SX Power Pack is designed to keep your HO and N Scale standard DC trains running smoothly. Revised in 2024, this power pack is 100% compatible with all Unitrack electrical accessories and is an in-kind replacement for previous Kato power packs. It is also upgradeable with alternative AC adapters that will allow greater output for larger layouts (sold separately). The Standard SX includes the controller with speed knob and reverser lever and also matches the pack supplied with M1 and M2 Master Series Oval Sets (sold separately).

Peco PLS-120 Smartswitch Board

Peco Point Motor

Clips directly into a Peco 00/H0 Setrack Turnout, either Left or Right Hand. No holes to drill, and this unit is pre wired. Can also be used with 00/H0 Streamline Turnouts. PL-26 Passing Contact Switches PL-50 Turnout Switch Modules PL-51 Turnout Switch Module Add ons

Peco PL1001 TwistLock Turnout Motor + Microswitch TwistLock a basic electric solenoid motor, for operating (in the main) turnouts and Microswitch for option to switch polarities, or to operate signals or panel lights etc. It is powered by a normal 16vDC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard. Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed. Dimensions Length = 42mm Hook to Hook = 42mm Depth = 25mm Depth with twin Microswitch = 66mm Extension Pin = 72mm Recommended to be used with: PL-26 Passing Contact Switches PL-34 Turnout Motor Wiring Harnesses PL-27 Switch Console Units

The PL series of Turnout Motors is tried and tested, over the last 40 years we have sold literally millions of these motors. Simple, reliable and good value. An extended drive pin is fitted, use the PL-9 Mounting Plate to attach this unit to the underside of the baseboard. Attaching PL-13 and 15 Switches will enable switching for automatic polarity etc. PL-26 Passing Contact Switches PL-34 Turnout Motor Wiring Harnesses PL-27 Switch Console Units  

TwistLock a basic electric solenoid motor, for operating (in the main) turnouts. It is powered by a normal 16vDC supply (and can take up to 3 amps) and is fully compatible with all PECO turnouts up to O gauge (and can handle many other proprietary brands too). But no longer will any soldering of wires to the terminals be necessary, nor the cutting of large holes in the baseboard. Each motor is supplied with a template, which the modeller uses to accurately mark the position of three holes that need to be drilled. The two outer holes are used to attach mounting studs beneath the baseboard. The larger centre hole is where the drive pin of the motor is positioned and threaded through the tie bar of the turnout. The motor is then simply twisted, and locked, into position and will remain firmly attached when operated. An extra operating bar, and spacers for the studs is included with every motor, enabling the above-board mounting of the motor where needed. Recommended to be used with: PL-26 Passing Contact Switches PL-34 Turnout Motor Wiring Harnesses PL-27 Switch Console Units