HOBBY TOOLS (1090)

Revell Contacta Professional for precise gluing. With the needle-fine cannula, micro-precise bonding can be carried out on tiny details and on the edges of transparent parts. Features With plastic welding effect Liquid consistency of the adhesive Needle-thin cannula for precise gluing Suitable for gluing small parts Subsequent adhesive application possible

Micro Set is a very versatile decal setting solution that does several things to Microscale Decals to improve application. Micro Set should be applied to the surface of the model where you will be sliding the decal off the paper backing. Micro Set prepares the surface with special wetting agents that cut the oils in new paint and converts the adhesive on the back of the decal to a stronger and longer lasting one. In addition, Micro Set slightly softens the decal film to make it more flexible so that it will conform better to the model's surface. Better adhesion of the decal to the model prevents tiny air bubbles from forming and results in an invisible carrier film for the so-called "painted on look." To apply Micro Set: Use a soft flat artist's brush and apply Micro Set where you are going to apply the decal. Then slide the decal off the backing paper using a small pointed tip synthetic bristle brush to carefully position the decal in its proper position. Blot the decal carefully with a tissue or paper toweling, being careful not to disturb its position. Allow the decal to dry overnight. It will then be ready for a protective coat of Micro Coat Flat, Satin or Gloss.

Micro Sol setting solution is for the most difficult irregular surfaces to be found on models. It completely softens the Microscale Decal, allowing it to drape down onto the surface of the model, conforming perfectly to surface irregularities without distortion. The most amazing results in seemingly impossible places are possible because Micro Sol actually makes the decal part of the painted surface. For that reason, you should coat Micro Sol on for only a few seconds and then leave it alone. It does the work. Do not touch until the decal has dried, as the decal is very soft at this stage and could be easily damaged. For the best results, first apply Micro Sol to prepare the surface and enhance the adhesive. Make sure the surface is free of particles that could get under the decal's film and cause a blemish. Then, when everything is dry enough that the decal will not move easily, apply Micro Sol with a small flat brush. Apply with as few strokes as possible so a not to disturb the decal. Then allow the decal to dry without disturbing it. One application is enough in most cases but, if necessary, a second application of Micro Sol can be helpful.

Standard Yellow-Grey Putty is Milliput's general purpose grade - it has been used for many years for the toughest tasks. Typical applications: Filling dents and scores in metal, plastics or woods Repairing water and fuel systems Caulking, filling and sealing on fiberglass, metal and wooden boat decks and hulls Modelmaking Jewellery making Sculpting Picture frame restoration Plumbing repairs Underwater applications Temporary repairs for car petrol tanks, batteries, radiators and exhausts

The Milliput Superfine White is a versatile epoxy putty that is perfect for various crafting and modeling projects. It is easy to mix and mold, allowing you to create intricate details and smooth finishes. Features Easy to mix and mold Creates smooth finishes Ideal for crafting and modeling projects Versatile and can be used on various materials Dries to a hard and durable finish Can be sanded, drilled, and painted over Suitable for small to medium-sized projects.

The most recent addition to their range of options, Milliput Black is ideal if you're working with a black surface & want to match the colour without painting it afterwards. Originally intended for industrial & DIY use, this incredibly versatile material was soon popularised by modelmakers for filling gaps in metal models, converting stock figurines, making buildings & producing master models for commercial purposes. By mixing the two parts included, this soft & highly adhesive putty will begin to gradually solidify to a resilient, rock hard finish over the course of several hours. Once fully cured, it can then be painted, sculpted, sanded & more. Heat-resistant up to 130º and able to set underwater, Milliput is an excellent adhesive that bonds not only to itself, but also wood, brick, cement, metals, concrete, plastic, glass & more. Stored correctly, this product has a shelf life of around 2 years.To help ensure this, store in cool, dry conditions & reseal packaging after each use. Features Two-part epoxy putty Soft, adhesive & versatile Mix equally to begin hardening Dries to a rock solid finish in 3-4hrs Sets underwater & heat resistant to 130º Able to be painted, sculpted, sanded, drilled & more! Uses include (but are not limited to) Modelling Sculpting Cast iron work Jewellery making Antique clock repair

Milliput Terracotta 2-part epoxy is a versatile and durable adhesive putty that, once mixed, can be shaped and applied to various surfaces for repairs, sculpting, and modeling projects with a natural terracotta finish.

IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R/C car tires. IC-2000™ has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available. Works Best On Glass & Metal Fiberglass Hard Plastics Rubber Reinforcing Works Good On Balsa Wood Soft Wood Hard Wood Ceramics Laminating Water-Resistant Directions Screw on top and cap unit to puncture the seal on the tube Remove cap and apply IC-2000™ CA to one side of the parts being joined, then hold them tightly together for 10-25 seconds for shock resistant joints. For larger bonding areas, apply serpentine beads of the CA, allowing for the spreading of the adhesive. For maximum flexibility, do not use with an accelerator. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 250º F. Top and tip can be soaked in acetone for cleaning.

Light and fluid putty with a water-based formula, ideal to fix fit defects or gaps on scale models of vehicles and figures. It can be applied with a brush, spatula or using the dispenser in the available format. Dries with a matt white finish. The applications can be primed or painted without any problem. It can be diluted to represent textures on surfaces (casting in armor, rust, etc.). Safety Always follow the information on the product label. Contains 1,2-benzisothiazol-3(2H)-one, Reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2 H-isothiazol-3-one (3:1). May cause allergic reactions.

The name RASER is derived from combining the two words GATE + ERASER. It's a revolutionary sanding tool that cleanly removes gate(nub marks) without scratches. Celebrating the two year anniversary, we have renamed it to RASER ORIGIN with a newly designed case. Experience the new way of removing gate(nub marks) without any stress. RASER ORIGIN specializes in gate(nub marks) removal using its proprietary Super-Nano Technology, which provides sanding experience powerfully, yet it leaves no scratches on the surface. Its tool for complete gate(nub marks) removal. More advanced than ever, Super-Nano technology is highly manufactured with precision and is far sharper than its predecessor. The sanding force of RASER ORIGIN is equivalent to 400 grit but leaves no scratches on the surface. RASER series have a handcrafted rounded finish by smoothing out the sharp edges. It cleanly removes the gate-marks without damaging the surface even when the sanding angle is off-balanced. When sanding with a typical glass file, it can scratch the surface with its edge if the sanding angle is off-balanced. However, RASER series are engineered with handcrafted soft edges to overcome such issues and it goes through a strict QA process to ensure easy and safe use by any users from novice to expert. Features Specialized tool for nub mark removal with Super-Nano Technology Leaves no scratches, which shortens sanding process Convenient use on the narrow surface and small parts Highly durable structure enables semi-permanent use Handcrafted smooth edge processing makes it safe and easy to use by users of all ages The reusable storage case is convenient for keeping various tools

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. Works Best On Rubber White Foam Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Super-Gold+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading ofthe adhesive. Insta-Set™ accelerator must be used when bonding two pieces of foam together. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Designed for enhancing the gloss coat of a finished model. Not for use on metal or bare plastic. Ideally applied with a soft polishing cloth and gentle buffing. Protects item from harsh handling and exterior conditions.

BALANCER GRAY is a special polisher developed with a proprietary technology called M620 which can produce up to 2000 grit surface from a 600 grit surface. This fast and effective tool is recommended for everyone from beginners to advanced users.Includes 3 per pack After achieving the 600 grit surface, use the BALANCER GRAY to smooth the surface similar to when using 2000 grit sandpaper. BALANCER GRAY can be used in either side. BALANCER GRAY can be cut into smaller sizes for more detailed and precise polishing on small areas. Cleaning: Use GUNPRIMER's DUST BRUSH or masking tapes to clean the dust and debris to recover the performance of the BALANCER for longer lasting use.

Ultimate ultra-thin single-edge structure brings excellent performance and efficiency!  GodHand Ultimate Nipper 5.0 is designed for the ultimate cut with a strong focus on gate cutting. When trying to slice-cut a 3 mm dia. runner, the blade moves in smoothly and finishes cutting without sound. The sharpness of the cutting edge achieves a smooth cut surface as if sharpened with a design knife and minimizes plastic whitening (a phenomenon in which the cut section turns white). Compared to most nippers, the cut surface is much cleaner and neater, which makes it a good choice for those who want to complete plastic models without painting. For those who paint plastic models, the cutting surface remains smooth and clean even if the blade is cut along the part without leaving a gate, thus shortening the time for gate processing with files or knives. When cutting out small parts, parts are less likely to fly away, reducing the need to search for missing parts. The standard force for cutting 3 mm dia. plastic is 2 kg or less. (General nippers are 3.5 kg to 10 kg) Cutting Edge and Single-Edged Structure Designed for Superior Sharpness GodHand Ultimate Nipper 5.0 superior sharpness comes from its thinly refined cutting edge and single-edge structure for a clean cutting. Ultra-thin cutting edge by craftsmanship Ultimate Nipper’s well-crafted cutting edge is as thin and sharp as a knife.It is created one by one through blade edging and sharpening by well-experienced craftspersons in Tsubame-Sanjo, Niigata Prefecture, a region famous for its cutlery. Single-edge structure for clean cutting Ultimate Nipper adopts a single-edged blade structure for clean cutting surfaces. Single-edged blade structure refers to a design in which one side of the blade is a cutting blade, and the other side is a cutting board blade. The blade is named ‘single-edged’ because only one blade (cutting edge) cuts on one side.  Specification Material: Special tool steel (made by Kobe Steel, Ltd.) Total length: approx. 120 mm Weight: approx. 60 g Blade hardness: ≧ HRC58 Single-edge specification Blade breakage prevention stopper Over-opening prevention pin Spring loaded Soft grip With original nipper cap Cutting capacity Target materials: Plastic (PS resin, PP resin, ABS resin, PE resin) only Cutting capacity: Materials of < 3 mm dia. However, transparent and translucent PS resins are limited to < 1 mm dia for hardness.

GodHand "Normal Nipper" has undergone a model change! Ideal for plastic kit gate cuts and runner cuts! "Ordinary nippers" are "universal nippers" that do not have special specs and can be used normally by anyone in any situation. To support the ultimate nipper. It is recommended for the first nipper debut. Safely cut various materials! The simple blade structure has a rough finish on the cross-section, but the strength of the blade is high by that amount, including plastic. Easily cuts various materials. The "ordinary nippers" have sharpness grade 3 (in-house standards), so you can see whitening compared to the grade 5 "ultimate nippers". Instead, compared to the ultra-thin single-edged ultimate nipper, there is no need to worry about the blade breaking, so even beginners can use it with confidence. The degree of opening of the blade does not depend on the spring! New spring structure "packing spring" adopted! When you grip it to a certain position, the stopper is released and you can open it fully. Overall length: about 130mm Grip thickness: about 12mm (thickest part) Weight: about 55g Material: Kobe Steel (JAPAN) special tool steel Blade hardness: HRC45-55 Cutting capacity: Plastic φ3mm or less (PS, PP, ABS, PE resin/metal cutting is not possible) Clear material runners are also supported! Notes It is possible to cut copper/aluminum wire 1mm and stranded wire 2mm due to its structure, but if it is cut, it will not be covered by the warranty. For safety, please wear protective glasses and gloves. There is a risk that the cut object may fly. Make sure that there are no people around and that there are no fragile objects before starting work. Do not pry things with a knife or touch them directly. Do not apply a load exceeding the cutting capacity. Hard wires such as metal wires cannot be used. Apply oil to the shaft and cutting edge to prevent rust. Keep the blade closed and out of reach of small children.

This is a two fluid ounce Pump Spray bottle of Bob Smith Industries INSTA-SET™ Foam Safe CA Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

ICKYSTICKY RC TYRE GLUE is specifically formulated for gluing plastic to rubber.  It is a super-thin, quick-setting cyanoacrylate with superior wicking action, meaning it will flow easy in between the tyre and the rim.  Includes 4 precision tips that can be cut to length.+

Ickysticky Ca Activator Is A Single Component, Solvent Based Surface Accelerator Designed To Increase The Speed Cure Of Ickysticky Range Of Ca Glues. This Product Works Best On: Ceramic Glass Metal Paint Rubber Aluminium Steel Fibreglass Wood Most Plastics Applications: Forces Immediate Cure Of Cyanoacrylate Adhesives. Use Pre Or Post-Applied To The Bond. Use For Difficult To Bond Material Combinations. Fast Acting Formula. Note: This Product Is Acetone Based. Do Not Use On Clear Plastic As This Will Cause The Plastic To Haze. Not Recommended For Painted Surfaces As It Will Remove Paint.

Gundam Marker Inking / Extra Fine Type can be used to carve concave lines and recessed areas of Gunpla to add definition and emphasize the three-dimensional effect. It can easily increase the realism of your model without painting. If you are using it on unpainted parts, you can erase any excess with an eraser. There are three colors, so please use them according to the color of the object you are painting and the expression you want to use. Usage examples: Black: For dark colored parts such as white, blue, and gray, or for strong, firm expressions Gray: For light colored parts such as white, or for slightly subdued expressions Brown: For red or gold-plated parts *This product is primarily designed to be applied directly over molded plastic parts of Gunpla models. If used over a painted surface with Gundam Marker Paint, Mr. Color, Gundam Color, or Water-Based Hobby Color, it will melt the painted surface and may leave a stain on the overflowing area. Please note that the melted paint may clog the felt tip of the pen, making it difficult for the ink to come out. *Cannot be used with the Gundam Marker Airbrush System. *When applying on a painted surface, please use the wipe-off type marking pen (GM20/21) or the mechanical pencil type GP01 .