BOB SMITH INDUSTRIES (27)

IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R/C car tires. IC-2000™ has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available. Works Best On Glass & Metal Fiberglass Hard Plastics Rubber Reinforcing Works Good On Balsa Wood Soft Wood Hard Wood Ceramics Laminating Water-Resistant Directions Screw on top and cap unit to puncture the seal on the tube Remove cap and apply IC-2000™ CA to one side of the parts being joined, then hold them tightly together for 10-25 seconds for shock resistant joints. For larger bonding areas, apply serpentine beads of the CA, allowing for the spreading of the adhesive. For maximum flexibility, do not use with an accelerator. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 250º F. Top and tip can be soaked in acetone for cleaning.

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. Works Best On Rubber White Foam Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Super-Gold+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading ofthe adhesive. Insta-Set™ accelerator must be used when bonding two pieces of foam together. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

This is a two fluid ounce Pump Spray bottle of Bob Smith Industries INSTA-SET™ Foam Safe CA Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Works Best On All Cyanoacrylates Directions Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour. Works Best On Hard Wood Glass & Metal Works Good On Balsa Wood Soft Wood Fiberglass Ceramics Hard Plastics White Foam Reinforcing Directions QUIK-CURE™ 5 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. QUIK-CURE™ is the least temperature sensitive of our epoxies. It will cure in temperatures down to 40˚F. Temperatures above 90˚F shorten the working time before the epoxy begins to set up from 5 to less than 4 minutes. QUIK-CURE™ bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. QUIK-CURE’S™ lack of brittleness allows it to form lasting bonds on materials as different as balsa wood and glass; however, it is not recommended for areas subject to long-term immersion in water. Cured QUIK-CURE™ can be coated with polyester resin without affecting the curing of the resin. Full cure in less than 15 minutes.

This is a one ounce bottle of Bob Smith Industries Foam-Cure Foam Safe Glue. This crystal clear glue is EPP foam safe and sets with a flexible bond. Regular CA glue cures stiff, but the flexibility of the Foam-Cure glue allows for better shock absorption and bond consistency. The quick set time is 15-30 minutes. For faster curing, pull joint apart and let Foam-Cure air dry for 30 seconds - 10 minutes before rejoining the parts. The full cure time is about 12 hours. It may be necessary to use tape to hold parts in place during cure.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. Works Best On Rubber White Foam Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Super-Gold+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading ofthe adhesive. Insta-Set™ accelerator must be used when bonding two pieces of foam together. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Works Best On Balsa Wood Soft Wood Works Good On Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Water-Resistant Reinforcing Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE™ has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE™ is usually the least expensive option for this application. Works Best On Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Reinforcing Works Good On Balsa Wood Water-Resistant Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

SUPER-GOLD™ and SUPER-GOLD+™ are our odourless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorption. Whenever a large amount of CA is to be used in such applications as saturating fibreglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL™ that you want. IC-GEL™ is an excellent putty for plastic models. It will fill any void and can be formed to many shapes. Applying INSTA-SET™ allows IC-GEL™ to be sanded or filed to final shape in less than 20 seconds. Autobody repairmen have finished their jobs in a fraction of the time by using IC-GEL™ with the additional advantage over normal body putties of superior bonding to metal surfaces. IC-GEL's™ most popular application is for the bonding of fragments of live coral (frags) to underwater rocks in aquariums. It has proven to be non-toxic to aquatic organisms and provides instant bonding for the propagation of the coral. IC-Gel has a superior shelf life of over three years and its application nozzle makes it the easiest of all CAs to apply. Works Best On Water-Resistant Reinforcing Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Directions Screw on top and cap unit to puncture seal on the tube. Remove cap and apply IC-GEL to one surface, and then hold parts tightly together. Sets in 10-25 seconds. Replace cap immediately after use. Store in cool dry place.

Insta-Flex™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated with INSTA-SET™. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE™, INSTA-FLEX™ still has good penetrating qualities and its application can be easier to control. For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when INSTA-FLEX™ is applied. INSTA-FLEX™ has a different, less irritating odor compared to regular CA's, but still can not be used on white foam. INSTA-FLEX™ has also proven to be superior when bonding anodized aluminum. Works Best On Balsa Wood Glass & Metal Rubber CA Hinges Works Good On Soft Wood Hard Wood Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE™ has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE™ is usually the least expensive option for this application. Works Best On Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Reinforcing Works Good On Balsa Wood Water-Resistant Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Works Best On Balsa Wood Soft Wood Works Good On Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Water-Resistant Reinforcing Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure™ Super Glue from Bob Smith Industries is a fast-acting cyanoacrylate adhesive with an ultra-thin viscosity, designed for precision bonding in tight-fitting joints. Its water-like consistency allows it to wick deep into seams through capillary action, making it perfect for woodworkers, model builders, and hobbyists needing a quick, reliable bond. Insta-Cure™ cures in just seconds, forming strong, lasting joints that go beyond surface adhesion—especially effective with porous materials like balsa wood. For best results, hold parts tightly together while applying the glue around the edges of the joint. Fast-Acting Adhesion with Deep Penetration Insta-Cure™ excels in applications where tight joints and quick bonding are essential. Its thin formula seeps deeply into porous surfaces like balsa wood, creating a bond that is both strong and long-lasting. The adhesive sets in seconds, speeding up assembly times for modelers and craftsmen alike. While its vapor may cause minor irritation, its performance and precision make it a top choice for serious hobbyists. Whether you're repairing models or crafting intricate wood structures, Insta-Cure™ ensures clean, gap-free results with minimal effort. Features Ultra-thin, water-like viscosity Wicks into joints via capillary action Cures in just seconds Ideal for tight-fitting seams Perfect for balsa wood and other porous materials Creates deep, strong bonds beyond surface level Fast-drying for efficient assembly Can cause mild eye or nose irritation from vapor

Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.

IC-LOC™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be disassembled with standard hand tools if required. Works Good On Threads of fasteners Bolts Screws Nuts Directions Shake well, then apply IC-LOC™ Blue to the clean and dry threaded areas before assembling non-plastic parts. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Blue is anaerobic and cures in the absence of air, which occurs when a bolt, screw or nut is tightened. IC-LOC™ Blue prevents loosening of fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Blue seals and prevents rusting of threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Remove residue with a damp cloth.

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. Works Best On Rubber White Foam Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Super-Gold+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading ofthe adhesive. Insta-Set™ accelerator must be used when bonding two pieces of foam together. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Features Ideal for the mounting of rubber tires onto R/C car wheels. It is available in our 3/4 oz Pocket CA bottle. ULTRA CURE can be used in many other applications that require a slightly thicker than CA and will bond virtually everything.

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner. Works Best On EPP Foam EOP Foam Clear Canopy Paper and Crafts Directions Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.