Hobby Glue (250)

Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Works Best On Balsa Wood Soft Wood Works Good On Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Water-Resistant Reinforcing Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

This is a one ounce bottle of Bob Smith Industries Foam-Cure Foam Safe Glue. This crystal clear glue is EPP foam safe and sets with a flexible bond. Regular CA glue cures stiff, but the flexibility of the Foam-Cure glue allows for better shock absorption and bond consistency. The quick set time is 15-30 minutes. For faster curing, pull joint apart and let Foam-Cure air dry for 30 seconds - 10 minutes before rejoining the parts. The full cure time is about 12 hours. It may be necessary to use tape to hold parts in place during cure.

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ and FINISH-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours. Works Best On Glass & Metal White Foam Water-Resistant Reinforcing Works Good On Balsa Wood Soft Wood Hard Wood Fiberglass Hard Plastics Laminating Directions SLOW-CURE™ 30 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. SLOW-CURE™ has the highest strength of our epoxies and should be applied in temperatures above 70°F. SLOW-CURE™ maintains it’s strength in both the lowest and highest temperature ranges of our line of epoxies. SLOW-CURE™ bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. SLOW-CURE™ works best for forming reinforcing fillets on joints and can be mixed with microballons or other fillers to form putty-like consistency. SLOW-CURE™ is waterproof and forms superior bonds if you’re willing to wait overnight. It has better penetration of porous surfaces for better bonding. Full cure in 6-8 hours.

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour. Works Best On Hard Wood Glass & Metal Works Good On Balsa Wood Soft Wood Fiberglass Ceramics Hard Plastics White Foam Reinforcing Directions QUIK-CURE™ 5 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals. QUIK-CURE™ is the least temperature sensitive of our epoxies. It will cure in temperatures down to 40˚F. Temperatures above 90˚F shorten the working time before the epoxy begins to set up from 5 to less than 4 minutes. QUIK-CURE™ bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. QUIK-CURE’S™ lack of brittleness allows it to form lasting bonds on materials as different as balsa wood and glass; however, it is not recommended for areas subject to long-term immersion in water. Cured QUIK-CURE™ can be coated with polyester resin without affecting the curing of the resin. Full cure in less than 15 minutes.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

ICKYSTICKY EXTRA THIN CEMENT is a solvent based adhesive formulated to bond polystyrene plastic, commonly used in making plastic model kits. Also perfect for using on styrene sheets when creating unique and one-of-a-kind pieces. Can be used: PRE-ASSEMBLY – apply to one part and bring the two pieces together. POST ASSEMBLY – parts are held together or pre-fitted. Features This formula has excellent capillary action and will run along a seam or join and weld the two pieces together.   The cap has a fine, pointed brush, allowing precise application and easy reach into small spaces. The brush is long in length to reach the bottom of the bottle. Bottle base dimensions 42mm x 42mm

If there ever was a modelers' secret, this is it. Micro Kristal Klear can do so many things, you will not believe that any product can make such a big difference in the appearance of your models. First, Micro Kristal Klear is a liquid that can be used to form very real looking small windows up to 1/4" in size. It also is an adhesive for mounting clear plastic parts, windows, etc., on models. It can be used to make lenses both clear and colored with the addition of a little food coloring. What really makes a remarkable difference in your models is the simple fact that the clear parts can be joined to the painted parts with a completely clear adhesive. What this means is that you do not have to mask around the clear parts, something that is rarely completely successful any way. Plus the sills which are painted can be seen through the Micro Kristal Klear for the most realistic looking windows you will see on a model. What the pros like best is that it is fast and easy and stays clear. It cleans up with water while wet and is waterproof when dry. You can tell when it's dry because it turns from milky white to clear. If you need a super strong and flexible adhesive for wood, plastic, paper or most combinations of dissimilar materials, this is a handy thing to have. For the making of small windows, you just dip a toothpick in this thick liquid and apply a little all around the edges. Then, holding the toothpick as flat as you can to the opening, draw it across from one side of the opening to the other. You will pick up a bubble which will form a very thin window of scale thickness that is also strong and flexible. When installing larger clear parts, paint the model first. Just apply a little Micro Kristal Klear along the edges to be joined, put in place and let dry.

ICKYSTICKY Thick Foam Safe CA is a thick viscosity cyanoacrylate adhesive with low odour and low-blooming characteristics. This technology offers excellent product performance and ease of processing. Eliminates the need for ventilation and reduces frosted residues in critical cosmetic bonding. This product works best on: Foam Board Xps Foam Eps Foam Cell Foam Aluminium Fibreglass Carbon Fibre Balsa Wood Resin Ceramic Acrylic Wood Pvc Latex Polystyrene Polymide Polycarbonate Petg Ply Wood Peek Applications Ideal For Clear Plastics, Reduced Blooming/Frosted Residue. Bonding Applications Where Ventilation Is A Problem. Ideal For Critical Cosmetic Bonding. Suitable For A Wide Variety Of Assembly Of Industrial And Medical Devices.

The world's best canopy glue. 560 dries clear making it the perfect glue to use for attaching airplane canopies and vacuum formed ABS parts. The excellent shock resistant flexible bond means your airplane parts will stay put even when subject to high vibration and extreme speeds. 560 is also an excellent craft glue. The nontoxic and water based formula means kids can safely use it for their special projects.

Fills gaps. Works well on harder woods such as Bass and Spruce, even works on oily surfaces! Some uses besides hobbies and crafts include; jewelry manufacturing and repair, taxidermy, pool cue tips, darts, archery, knife making, mold and pattern making, furniture refinishing and antique repair, and for fishing, fly line splicing and fly tying. Wood turners and manufactures of custom wood products appreciate the ability of ZAP-A-GAP CA+ to help save their projects by filling in and bonding cracks that often occur in expensive hard woods. Allows 7 to 10 seconds for positioning. Features Superior gap filling formula Medium viscosity Allow approximately 7-10 seconds for part positioning Average of 20 seconds for curing Works on oily surfaces Works best on Aluminum Ceramic Leather Metal Most Plastics Pottery Rubber Veneer Wood

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. Works Best On Rubber White Foam Works Good On Balsa Wood Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Laminating Water-Resistant Reinforcing CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Super-Gold+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading ofthe adhesive. Insta-Set™ accelerator must be used when bonding two pieces of foam together. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.

All-purpose adhesive and sealant.Features Bonds wood to fiberglass, metal to wood, plastic to metal, just aboutanything to anything with a strong flexible bond. An excellent adhesive for today's high tech composite airplane, boat,and car hobby products, and great for all of those fix-it, mend-it,seal-it, and stick-it jobs around the house. The excellent shock resistant flexible bond means your parts willstay put even when subject to high vibration and extreme shocks. Great for craft work, including wood, clay, plaster, glass andfabrics. Takes 24 to 36 hours to full cure and reach maximum strength. Handles in 1 to 2 minutes. Dries clear. Remains flexible. Works where others won't! Zap Goo bonds can be cut with a razor knife. Includes One Tube of Zap Goo One Applicator Nozzle

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE™ has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE™ is usually the least expensive option for this application. Works Best On Soft Wood Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Reinforcing Works Good On Balsa Wood Water-Resistant Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Works Best On Balsa Wood Soft Wood Works Good On Hard Wood Glass & Metal Fiberglass Ceramics Hard Plastics Rubber Laminating Water-Resistant Reinforcing Directions Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On Balsa Wood Ceramics Works Good On Soft Wood Fiberglass Hard Plastics Water-Resistant CA Hinges Directions Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure™ CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure™ along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure™. Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220º F. Soak extender tip in acetone for cleaning.