Hobby Glue (148)

Revell Contacta Professional for precise gluing. With the needle-fine cannula, micro-precise bonding can be carried out on tiny details and on the edges of transparent parts. Features With plastic welding effect Liquid consistency of the adhesive Needle-thin cannula for precise gluing Suitable for gluing small parts Subsequent adhesive application possible

Micro Set is a very versatile decal setting solution that does several things to Microscale Decals to improve application. Micro Set should be applied to the surface of the model where you will be sliding the decal off the paper backing. Micro Set prepares the surface with special wetting agents that cut the oils in new paint and converts the adhesive on the back of the decal to a stronger and longer lasting one. In addition, Micro Set slightly softens the decal film to make it more flexible so that it will conform better to the model's surface. Better adhesion of the decal to the model prevents tiny air bubbles from forming and results in an invisible carrier film for the so-called "painted on look." To apply Micro Set: Use a soft flat artist's brush and apply Micro Set where you are going to apply the decal. Then slide the decal off the backing paper using a small pointed tip synthetic bristle brush to carefully position the decal in its proper position. Blot the decal carefully with a tissue or paper toweling, being careful not to disturb its position. Allow the decal to dry overnight. It will then be ready for a protective coat of Micro Coat Flat, Satin or Gloss.

Micro Sol setting solution is for the most difficult irregular surfaces to be found on models. It completely softens the Microscale Decal, allowing it to drape down onto the surface of the model, conforming perfectly to surface irregularities without distortion. The most amazing results in seemingly impossible places are possible because Micro Sol actually makes the decal part of the painted surface. For that reason, you should coat Micro Sol on for only a few seconds and then leave it alone. It does the work. Do not touch until the decal has dried, as the decal is very soft at this stage and could be easily damaged. For the best results, first apply Micro Sol to prepare the surface and enhance the adhesive. Make sure the surface is free of particles that could get under the decal's film and cause a blemish. Then, when everything is dry enough that the decal will not move easily, apply Micro Sol with a small flat brush. Apply with as few strokes as possible so a not to disturb the decal. Then allow the decal to dry without disturbing it. One application is enough in most cases but, if necessary, a second application of Micro Sol can be helpful.

ICKYSTICKY Thin CA is a thin, quick-setting, penetrating formula that bonds through oily or dirty surfaces. This product works best on: China Aluminium Pottery Fibreglass Rubber Resin Wood Metal Features Superior Penetrating Formula Thin Viscosity Bonds And Cures In 1 To 5 Seconds Works On Most Materials Excellent Wicking Action Pin Cap To Prevent Nozzle Clogging.

The Tamiya Super-Glue CA Cement Accelerator enables quicker curing of CA cement. Apply the accelerator to one cementing surface and the CA cement to the other. A strong bond will quickly form when the two surfaces are pressed together. This is ideal for attaching small photo-etched parts or parts with a very small cementing surface. The bottle's cap has an applicator brush to ensure easy application. This is an alcohol-based accelerator that keeps damage to plastic parts to a minimum. One bottle contains 10ml.

Mr. Mark Setter is a decal adhesive. It is used to firmly attach decals to painted surfaces. It is particularly effective when used on old decals that have lost their adhesion or decals that do not have strong adhesive properties. Italso contains ingredients that soften decals. Apply a small amount to the location where you want to attach the decal, and then place the decal on top of it. The adhesive bonds the decal to the painted surface, making it difficult to peel off even after drying. The decal is softened rapidly by the softening solvent, so if too much is applied, the decal itself may melt or the painted surface may be eroded. Applying it on top of an attached decal has some effect, but basically you should apply it under the decal. This product is water-soluble. Adding water appropriately will dilute the effect of the solvent and prevent rapid softening. Depending on the painted surface and type of decal to be used, it is recommended to dilute with water before use. After applying the decal, lightly press the decal with a lightly dampened Mr. Cotton Swab, Mr. Clean Stick 2, or a dust-free cloth to ensure that the decal adheres firmly to the surface of the part. At that time, wipe off excess Mr. Mark Setter with water to prevent it from softening too much. Using a damp cotton swab or similar will neutralize the Mark Setter and prevent it from becoming too soft with the solvent. If the decal is hard and does not soften easily, apply a small amount of MS231 Mr. Mark Softer onto the decal and work it in. Be careful not to apply too much. If air bubbles get trapped between the decal and the part (silvering), after the decal has dried, carefully poke holes in the decal with a needle or craft knife. Then, by applying Mr. Mark Softer again, the decal will soften again, the air bubbles will disappear, and the decal will adhere firmly to the surface of the part. One way to prevent silvering is to use a glossy surface on the surface onto which the decal will be applied. The main ingredients used in the previous product have been changed to environmentally friendly ones and the product has been redesigned. The changes made to the product are as follows: The adhesive has been changed from an emulsion resin adhesive to an acrylic resin adhesive. The adhesive performance is improved compared to the previous version. When applying a decal, even if you apply a gloss clear coat and then mask it, the decal is less likely to be taken away by the masking tape. Softening effect is now stronger than before. It has more dissolving power for water-based hobby colors than previous products. This is particularly noticeable when the drying time is short, so please dry thoroughly and avoid applying a large amount. If you use it, it is best to dilute the Mark Setter with water to reduce its dissolving power before use. Although this will depend on factors such as the drying time of the coating, the amount used, and how it is wiped off, a dilution of approximately 30% is a good guideline.

ICKYSTICKY EXTRA THIN CEMENT is a solvent based adhesive formulated to bond polystyrene plastic, commonly used in making plastic model kits. Also perfect for using on styrene sheets when creating unique and one-of-a-kind pieces. Can be used: PRE-ASSEMBLY – apply to one part and bring the two pieces together. POST ASSEMBLY – parts are held together or pre-fitted. Features This formula has excellent capillary action and will run along a seam or join and weld the two pieces together.   The cap has a fine, pointed brush, allowing precise application and easy reach into small spaces. The brush is long in length to reach the bottom of the bottle. Bottle base dimensions 42mm x 42mm

ICKYSTICKY RC TYRE GLUE is specifically formulated for gluing plastic to rubber.  It is a super-thin, quick-setting cyanoacrylate with superior wicking action, meaning it will flow easy in between the tyre and the rim.  Includes 4 precision tips that can be cut to length.+

Cyano-Acrylate Cement Quick Type 2gm

The Army Painter Green Stuff is used by model makers and hobbyists for conversions, filling mold lines and sculpting miniatures.Green stuff hardens fast with a 20-30 minutes worktime for molding & only 8 hours to fully dry. Mix equal parts of yellow & blue putty until you get an even green colored putty.Use with super glue to glue larger components.Features Great for adding bits or hiding mold lines. Hardens fast when the two components are mixed. Fast and easy kneading.

Updated Bottle - Now 18ml!!! Reduces consistency and increases gloss, flow and transparency. Dries quickly, flexible and waterproof. Keep painting tools moist and clean with water. Do not use as final varnish.

QUICK SET Z-POXY is a premium two part epoxy adhesive. The 5 minute cure time means fast building and fast repairs. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. It does not get brittle with age and it's easy to mix: combine equal parts by volume. QUICK SET Z-POXY is handy to have at home for all types of fix-it jobs, woodworking, and furniture repair.QUICK SET Z-POXY fully cure in approximately 5 minutes, which allows you will have about 3 minutes of working time. To clean up any uncured or unmixed epoxy, use alcohol, isopropyl or methanol, either will work. Thinning of QUICK SET Z-POXY is not recommended. Mix Z-POXY in a plastic cup or on a non porous surface such as a piece flexible plastic. Mix only enough epoxy as needed. Excess epoxy cannot be saved once mixed. Since epoxies cure by an exothermic chemical reaction (give off heat), and heat can speed the curing of epoxy, mixing large amounts can shorten the pot-life if not quickly spread. If you need a longer working time, or need to thin the epoxy, use Z-POXY 30 MINUTE FORMULA (Item #PT-39). SYRINGE APPLICATION 5 MINUTE CURE CLEAR FORMULA TOUGH, PERMANENT BOND SHOCK AND VIBRATION RESISTANT EXCELLENT GAP FILLER

Thick and strong for high-stress areas.This Zap works well on hard woods such as Maple and Oak, or similar cabinet timbers. In modeling it's ideal for laminating wood parts and forming fillets. Because it's thick, it will not run. It forms a very clean even fillet around all types of joints. The high cured strength means it works great on higher stress areas.Allows 30 seconds for positioning and cures in 60 seconds or less. To accelerate cure time use ZAP Kicker Accelerator Pump!Works best on: Most Plastics, Rubber, Wood, Aluminium, Laminate & Metal.

Flexi-tips allow micro drops of glue to be placed in hard-to-reach areas. Features Allows for smaller drops Precision application Extension into hard-to-reach places Fits most brands of CA bottles  

Zap Z-Ends are 10 pcs extended tips and 38 cm (15 inches) of micro dropper tubing. These fir to the end of ZAP Superglue bottles to allow smaller drops of glue to be placed accurately in hard-to-reach places. Zap Z-Ends PT18 are suitable for thin and medium weight cyano acrylate glue, and fit most CA glue bottles. Features Smaller Drops Precision Application Extension into hard-to-reach areas Maximum use of bottle