HOBBY PAINTS (2244)

ACRYL/POLY THINNER X-20A 46ML Tamiya acrylic paints are made from water-soluble acrylic resins and are excellent for either brush painting or air-brushing. These paints can be used on styrene resins, Styrofoam, wood, plus all of the common model plastics. The paint covers well, flows smoothly and can be blended easily. Prior to curing, paint can be washed away with plain water.When airbrushing make sure to use any of the following Tamiya thinners: 81020, 81030, 81040, 81520, 87077. Features X designated colors have a glossy finish while XF designated colors are flat finish. The paint can be thinned for airbrushing using Tamiya X-20A Acrylic thinner. The paint can be also thinned for airbrushing using Tamiya Lacquer Thinner. Using Tamiya Lacquer Thinner will yield faster drying results and a harder finish. For better paint brushing results use Tamiya Paint Retarder (87114) for a smoother brushstroke free finish.

Aqueous Hobby Color is a paint line newly reformulated in 2020 and aimed to be a safer paint with a higher degree of user friendliness. Aqueous Hobby Color paint is water based, which means you will never run out of thinner/reducer – you can use regular water. Tool cleanup is also easier as you can use water. Aqueous Hobby Color paint does contain a mild solvent in it which helps a lot with the adhesion. Leveling capabilities of this paint are high, it provides a glossy finish with a light texture, creating an excellent paint finish.Gloss levels of the Aqueous paint can be adjusted using additives H-40 Flat Base can be mixed with any color and make the paint semi-gloss or even matte/flat. Mix ratio between 5% and 10% is recommended. Mr. Aqueous Hobby Colors are ready for a regular brush application. They are also airbrush friendly; however, it is recommended to reduce it before use with an airbrush. As we mentioned earlier, regular water can be used as a reducer, but for the best result we recommend using Mr. Aqueous Hobby Color Thinner (T-110 or T-111). Up to 150% of the reducer can be added to Aqueous paint for airbrush use. When spraying paints with an airbrush, 2-3 coats are recommended. For regular brush use 1-2 coats is enough. If painting a light color over a darker base surface, more layers of paint may be required.

A masking sheets with slits 1 mm or 2 mm in width. This saves time and effort to cut the masking tape while applying a scale to the masking when you need fine lines. Two sheets with slits of 1 mm and 2 mm in width, one each, are packaged. Specification 1 mm in width: 166 mm in length, 90 slits/sheet 2 mm in width: 166 mm in length, 45 slits/sheet

Aqueous Hobby Color is a very safe paint which has a high degree of user friendliness. Aqueous Hobby Color paint can be diluted with water if desired, while paint brushes can be cleaned and washed out in water. Ensuring that this is beforethe paint is dry. The solvent contained in Aqueous Hobby Color paint is very mild.It provides a glossy texture and very good levelling qualities (ie the smoothness of coated film of paint), resulting in a very good level of painted finish. In particular, the gloss level achieved with the use of Aqueous Hobby Color gloss paints is excellent. Gloss levels obtained using gloss coat Aqueous Hobby Colors can be adjusted by using H-40 Flat Base - mix approximately 5% of H-40 Flat Base to convert gloss colors to a matt finish, or 5 to 10% for a semi gloss finish. The percentage of Flat Base used can be adjusted to vary the amount of gloss level obtained. It is not necessary to dilute Aqueous Hobby Color for brush painting as a basic rule, but if using an airbrush to spray Aqueous Hobby Color, dilute the paint with 100 to 150% Mr.Aqueous Hobby Color Thinner (T-110 0r T-111).When brush painting, generally 1 to 2 coats are recommended, and 2 to 3 coats when using an air brush. If painting a light color over a darker base surface, more coats of paint may be required. *When painted on ABS resin parts, the paint penetrates into the resin and the parts become friable or develop cracks. Check the instructions in the assembly manual or on the parts runner and try to avoid painting on ""ABS resin parts"".

Aqueous Hobby Color is a very safe paint which has a high degree of user friendliness. Aqueous Hobby Color paint can be diluted with water if desired, while paint brushes can be cleaned and washed out in water. Ensuring that this is beforethe paint is dry. The solvent contained in Aqueous Hobby Color paint is very mild.It provides a glossy texture and very good levelling qualities (ie the smoothness of coated film of paint), resulting in a very good level of painted finish. In particular, the gloss level achieved with the use of Aqueous Hobby Color gloss paints is excellent. Gloss levels obtained using gloss coat Aqueous Hobby Colors can be adjusted by using H-40 Flat Base - mix approximately 5% of H-40 Flat Base to convert gloss colors to a matt finish, or 5 to 10% for a semi gloss finish. The percentage of Flat Base used can be adjusted to vary the amount of gloss level obtained. It is not necessary to dilute Aqueous Hobby Color for brush painting as a basic rule, but if using an airbrush to spray Aqueous Hobby Color, dilute the paint with 100 to 150% Mr.Aqueous Hobby Color Thinner (T-110 0r T-111).When brush painting, generally 1 to 2 coats are recommended, and 2 to 3 coats when using an air brush. If painting a light color over a darker base surface, more coats of paint may be required. *When painted on ABS resin parts, the paint penetrates into the resin and the parts become friable or develop cracks. Check the instructions in the assembly manual or on the parts runner and try to avoid painting on ""ABS resin parts"".

Aqueous Hobby Color is a very safe paint which has a high degree of user friendliness. Aqueous Hobby Color paint can be diluted with water if desired, while paint brushes can be cleaned and washed out in water. Ensuring that this is beforethe paint is dry. The solvent contained in Aqueous Hobby Color paint is very mild.It provides a glossy texture and very good levelling qualities (ie the smoothness of coated film of paint), resulting in a very good level of painted finish. In particular, the gloss level achieved with the use of Aqueous Hobby Color gloss paints is excellent. Gloss levels obtained using gloss coat Aqueous Hobby Colors can be adjusted by using H-40 Flat Base - mix approximately 5% of H-40 Flat Base to convert gloss colors to a matt finish, or 5 to 10% for a semi gloss finish. The percentage of Flat Base used can be adjusted to vary the amount of gloss level obtained. It is not necessary to dilute Aqueous Hobby Color for brush painting as a basic rule, but if using an airbrush to spray Aqueous Hobby Color, dilute the paint with 100 to 150% Mr.Aqueous Hobby Color Thinner (T-110 0r T-111).When brush painting, generally 1 to 2 coats are recommended, and 2 to 3 coats when using an air brush. If painting a light color over a darker base surface, more coats of paint may be required. *When painted on ABS resin parts, the paint penetrates into the resin and the parts become friable or develop cracks. Check the instructions in the assembly manual or on the parts runner and try to avoid painting on ""ABS resin parts"".

Introducing the New Mr. Hobby Marker Series! We are pleased to announce the arrival of the Mr. Hobby Marker Series in our marker lineup! The first release features water-based metallic colors that can be used for panel lining without affecting the underlying surface or material. These markers are perfect for adding metallic details to fine parts or for creating one-of-a-kind accents. Additionally, you can achieve weathering effects by using the separately sold blending pen to blend the colors seamlessly.

Good news for those who feel that the adhesive strength of regular masking tape is weak! The adhesive strength has been adjusted to be stronger, so it is easy to apply to parts made of materials that are difficult to apply, such as resin, and it is difficult to peel off. The material used is still ultra-thin Japanese paper, so it is a masking tape designed to be highly elastic and not easily leave uneven surfaces after peeling off

This high-end metallic color uses high-grade special pigments that have been ultra-finely refined using high-purity technology, resulting in a thin coating that produces a solid metallic color.

Mr. COLOR has long been regarded highly by modellers worldwide as a model paint that delivers an outstanding finish. A wide range of colours are available, and these are suitable for military tanks, aircraft, car models, robot models, and many more. Mr. COLOR is available in a wider range of colours and finishes than AQUEOUS HOBBY COLOR. Compared to AQUEOUS HOBBY COLOR, it has a faster drying speed and its paint film is stronger. SUITABLE FOR BOTH HAND PAINTING AND AIRBRUSHING. THINNING RATIO for Mr. COLOR BRUSH PAINTING 1 : 0.8~1.0 (Mr. COLOR : Mr. COLOR THINNER) AIRBRUSHING 1 : 1~2 (Mr. COLOR : Mr. COLOR THINNER) Mr. LEVELING THINNER IS RECOMMENDED FOR AIRBRUSHING Must only be thinned with Mr. COLOR THINNER, Mr. COLOR LEVELING THINNER or MR.COLOR RAPID THINNER.Do not thin with THINNER FOR AQUEOUS HOBBY COLOR and ACRYSION SOLVENT. CHOOSE AN APPROPRIATE THINNER Mr. COLOR THINNER: The most basic thinner for Mr. COLOR Mr. LEVELING THINNER: Slows down the drying speed. Recommended for gloss paints. Use this thinner to thin Mr. COLOR if airbrushing. Mr. RAPID THINNER: Speeds up the drying speed. Recommended for matt paints and metallic paints. MIXING CAN BE MIXED WITH Mr. COLOR Mr. COLOR GX, Mr. METALLIC COLOR GX, Mr. CLEAR COLOR GX Mr. COLOR 40TH ANNIVERSARY, Mr. CRYSTAL COLOR, Mr. SUPER METALLIC LASCIVUS CANNOT BE MIXED WITH AQUEOUS HOBBY COLOR ACRYSION, ACRYSION BASE COLORS CLASSY 'N DRESSY COLORS Mr. METAL COLOR AQUEOUS HOBBY COLOR and ACRYSION can be applied over a coat of Mr. COLOR.Mr. COLOR cannot be applied over a coat of AQUEOUS HOBBY COLOR and ACRYSION. HOW TO APPLY Mr. COLOR Apply 1 to 2 coats if painting with a paint brush, or 2 to 3 coats if airbrushing. After applying a coat of Mr. COLOR, let it dry for a few hours. After the first coat is completely dry, apply a second coat. TIP! Use T114 Mr. Paint Remover to remove paint from a surface. Clean the tools with Mr. COLOR THINNER or Mr. TOOL CLEANER. Mix approximately 5 to 10% of C30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. Mr. HOBBY TOPCOAT and SUPER CLEAR can be applied over a coat of Mr. COLOR. Do a test paint before you apply paint on your model kit. ATTENTION Put the lid back on after use. Store in a cool and ventilated place, away from direct sunlight. Use in a well ventilated area.

Mr. COLOR has long been regarded highly by modellers worldwide as a model paint that delivers an outstanding finish. A wide range of colours are available, and these are suitable for military tanks, aircraft, car models, robot models, and many more. Mr. COLOR is available in a wider range of colours and finishes than AQUEOUS HOBBY COLOR. Compared to AQUEOUS HOBBY COLOR, it has a faster drying speed and its paint film is stronger. SUITABLE FOR BOTH HAND PAINTING AND AIRBRUSHING. THINNING RATIO for Mr. COLOR BRUSH PAINTING 1 : 0.8~1.0 (Mr. COLOR : Mr. COLOR THINNER) AIRBRUSHING 1 : 1~2 (Mr. COLOR : Mr. COLOR THINNER) Mr. LEVELING THINNER IS RECOMMENDED FOR AIRBRUSHING Must only be thinned with Mr. COLOR THINNER, Mr. COLOR LEVELING THINNER or MR.COLOR RAPID THINNER.Do not thin with THINNER FOR AQUEOUS HOBBY COLOR and ACRYSION SOLVENT. CHOOSE AN APPROPRIATE THINNER Mr. COLOR THINNER: The most basic thinner for Mr. COLOR Mr. LEVELING THINNER: Slows down the drying speed. Recommended for gloss paints. Use this thinner to thin Mr. COLOR if airbrushing. Mr. RAPID THINNER: Speeds up the drying speed. Recommended for matt paints and metallic paints. MIXING CAN BE MIXED WITH Mr. COLOR Mr. COLOR GX, Mr. METALLIC COLOR GX, Mr. CLEAR COLOR GX Mr. COLOR 40TH ANNIVERSARY, Mr. CRYSTAL COLOR, Mr. SUPER METALLIC LASCIVUS CANNOT BE MIXED WITH AQUEOUS HOBBY COLOR ACRYSION, ACRYSION BASE COLORS CLASSY 'N DRESSY COLORS Mr. METAL COLOR AQUEOUS HOBBY COLOR and ACRYSION can be applied over a coat of Mr. COLOR.Mr. COLOR cannot be applied over a coat of AQUEOUS HOBBY COLOR and ACRYSION. HOW TO APPLY Mr. COLOR Apply 1 to 2 coats if painting with a paint brush, or 2 to 3 coats if airbrushing. After applying a coat of Mr. COLOR, let it dry for a few hours. After the first coat is completely dry, apply a second coat. TIP! Use T114 Mr. Paint Remover to remove paint from a surface. Clean the tools with Mr. COLOR THINNER or Mr. TOOL CLEANER. Mix approximately 5 to 10% of C30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. Mr. HOBBY TOPCOAT and SUPER CLEAR can be applied over a coat of Mr. COLOR. Do a test paint before you apply paint on your model kit. ATTENTION Put the lid back on after use. Store in a cool and ventilated place, away from direct sunlight. Use in a well ventilated area.

Mr. COLOR has long been regarded highly by modellers worldwide as a model paint that delivers an outstanding finish. A wide range of colours are available, and these are suitable for military tanks, aircraft, car models, robot models, and many more. Mr. COLOR is available in a wider range of colours and finishes than AQUEOUS HOBBY COLOR. Compared to AQUEOUS HOBBY COLOR, it has a faster drying speed and its paint film is stronger. SUITABLE FOR BOTH HAND PAINTING AND AIRBRUSHING. THINNING RATIO for Mr. COLOR BRUSH PAINTING 1 : 0.8~1.0 (Mr. COLOR : Mr. COLOR THINNER) AIRBRUSHING 1 : 1~2 (Mr. COLOR : Mr. COLOR THINNER) Mr. LEVELING THINNER IS RECOMMENDED FOR AIRBRUSHING Must only be thinned with Mr. COLOR THINNER, Mr. COLOR LEVELING THINNER or MR.COLOR RAPID THINNER.Do not thin with THINNER FOR AQUEOUS HOBBY COLOR and ACRYSION SOLVENT. CHOOSE AN APPROPRIATE THINNER Mr. COLOR THINNER: The most basic thinner for Mr. COLOR Mr. LEVELING THINNER: Slows down the drying speed. Recommended for gloss paints. Use this thinner to thin Mr. COLOR if airbrushing. Mr. RAPID THINNER: Speeds up the drying speed. Recommended for matt paints and metallic paints. MIXING CAN BE MIXED WITH Mr. COLOR Mr. COLOR GX, Mr. METALLIC COLOR GX, Mr. CLEAR COLOR GX Mr. COLOR 40TH ANNIVERSARY, Mr. CRYSTAL COLOR, Mr. SUPER METALLIC LASCIVUS CANNOT BE MIXED WITH AQUEOUS HOBBY COLOR ACRYSION, ACRYSION BASE COLORS CLASSY 'N DRESSY COLORS Mr. METAL COLOR AQUEOUS HOBBY COLOR and ACRYSION can be applied over a coat of Mr. COLOR.Mr. COLOR cannot be applied over a coat of AQUEOUS HOBBY COLOR and ACRYSION. HOW TO APPLY Mr. COLOR Apply 1 to 2 coats if painting with a paint brush, or 2 to 3 coats if airbrushing. After applying a coat of Mr. COLOR, let it dry for a few hours. After the first coat is completely dry, apply a second coat. TIP! Use T114 Mr. Paint Remover to remove paint from a surface. Clean the tools with Mr. COLOR THINNER or Mr. TOOL CLEANER. Mix approximately 5 to 10% of C30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. Mr. HOBBY TOPCOAT and SUPER CLEAR can be applied over a coat of Mr. COLOR. Do a test paint before you apply paint on your model kit. ATTENTION Put the lid back on after use. Store in a cool and ventilated place, away from direct sunlight. Use in a well ventilated area.

Mr. COLOR has long been regarded highly by modellers worldwide as a model paint that delivers an outstanding finish. A wide range of colours are available, and these are suitable for military tanks, aircraft, car models, robot models, and many more. Mr. COLOR is available in a wider range of colours and finishes than AQUEOUS HOBBY COLOR. Compared to AQUEOUS HOBBY COLOR, it has a faster drying speed and its paint film is stronger. SUITABLE FOR BOTH HAND PAINTING AND AIRBRUSHING. THINNING RATIO for Mr. COLOR BRUSH PAINTING 1 : 0.8~1.0 (Mr. COLOR : Mr. COLOR THINNER) AIRBRUSHING 1 : 1~2 (Mr. COLOR : Mr. COLOR THINNER) Mr. LEVELING THINNER IS RECOMMENDED FOR AIRBRUSHING Must only be thinned with Mr. COLOR THINNER, Mr. COLOR LEVELING THINNER or MR.COLOR RAPID THINNER.Do not thin with THINNER FOR AQUEOUS HOBBY COLOR and ACRYSION SOLVENT. CHOOSE AN APPROPRIATE THINNER Mr. COLOR THINNER: The most basic thinner for Mr. COLOR Mr. LEVELING THINNER: Slows down the drying speed. Recommended for gloss paints. Use this thinner to thin Mr. COLOR if airbrushing. Mr. RAPID THINNER: Speeds up the drying speed. Recommended for matt paints and metallic paints. MIXING CAN BE MIXED WITH Mr. COLOR Mr. COLOR GX, Mr. METALLIC COLOR GX, Mr. CLEAR COLOR GX Mr. COLOR 40TH ANNIVERSARY, Mr. CRYSTAL COLOR, Mr. SUPER METALLIC LASCIVUS CANNOT BE MIXED WITH AQUEOUS HOBBY COLOR ACRYSION, ACRYSION BASE COLORS CLASSY 'N DRESSY COLORS Mr. METAL COLOR AQUEOUS HOBBY COLOR and ACRYSION can be applied over a coat of Mr. COLOR.Mr. COLOR cannot be applied over a coat of AQUEOUS HOBBY COLOR and ACRYSION. HOW TO APPLY Mr. COLOR Apply 1 to 2 coats if painting with a paint brush, or 2 to 3 coats if airbrushing. After applying a coat of Mr. COLOR, let it dry for a few hours. After the first coat is completely dry, apply a second coat. TIP! Use T114 Mr. Paint Remover to remove paint from a surface. Clean the tools with Mr. COLOR THINNER or Mr. TOOL CLEANER. Mix approximately 5 to 10% of C30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. Mr. HOBBY TOPCOAT and SUPER CLEAR can be applied over a coat of Mr. COLOR. Do a test paint before you apply paint on your model kit. ATTENTION Put the lid back on after use. Store in a cool and ventilated place, away from direct sunlight. Use in a well ventilated area.

Mr. COLOR has long been regarded highly by modellers worldwide as a model paint that delivers an outstanding finish. A wide range of colours are available, and these are suitable for military tanks, aircraft, car models, robot models, and many more. Mr. COLOR is available in a wider range of colours and finishes than AQUEOUS HOBBY COLOR. Compared to AQUEOUS HOBBY COLOR, it has a faster drying speed and its paint film is stronger. SUITABLE FOR BOTH HAND PAINTING AND AIRBRUSHING. THINNING RATIO for Mr. COLOR BRUSH PAINTING 1 : 0.8~1.0 (Mr. COLOR : Mr. COLOR THINNER) AIRBRUSHING 1 : 1~2 (Mr. COLOR : Mr. COLOR THINNER) Mr. LEVELING THINNER IS RECOMMENDED FOR AIRBRUSHING Must only be thinned with Mr. COLOR THINNER, Mr. COLOR LEVELING THINNER or MR.COLOR RAPID THINNER.Do not thin with THINNER FOR AQUEOUS HOBBY COLOR and ACRYSION SOLVENT. CHOOSE AN APPROPRIATE THINNER Mr. COLOR THINNER: The most basic thinner for Mr. COLOR Mr. LEVELING THINNER: Slows down the drying speed. Recommended for gloss paints. Use this thinner to thin Mr. COLOR if airbrushing. Mr. RAPID THINNER: Speeds up the drying speed. Recommended for matt paints and metallic paints. MIXING CAN BE MIXED WITH Mr. COLOR Mr. COLOR GX, Mr. METALLIC COLOR GX, Mr. CLEAR COLOR GX Mr. COLOR 40TH ANNIVERSARY, Mr. CRYSTAL COLOR, Mr. SUPER METALLIC LASCIVUS CANNOT BE MIXED WITH AQUEOUS HOBBY COLOR ACRYSION, ACRYSION BASE COLORS CLASSY 'N DRESSY COLORS Mr. METAL COLOR AQUEOUS HOBBY COLOR and ACRYSION can be applied over a coat of Mr. COLOR.Mr. COLOR cannot be applied over a coat of AQUEOUS HOBBY COLOR and ACRYSION. HOW TO APPLY Mr. COLOR Apply 1 to 2 coats if painting with a paint brush, or 2 to 3 coats if airbrushing. After applying a coat of Mr. COLOR, let it dry for a few hours. After the first coat is completely dry, apply a second coat. TIP! Use T114 Mr. Paint Remover to remove paint from a surface. Clean the tools with Mr. COLOR THINNER or Mr. TOOL CLEANER. Mix approximately 5 to 10% of C30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. Mr. HOBBY TOPCOAT and SUPER CLEAR can be applied over a coat of Mr. COLOR. Do a test paint before you apply paint on your model kit. ATTENTION Put the lid back on after use. Store in a cool and ventilated place, away from direct sunlight. Use in a well ventilated area.

Mr Color hobby paint is a paint that has long been regarded highly by modelers world wide as a model paint that delivers an outstanding finish. There are a large number of colours and colour types available, which are suitable for painting almost all models. Generally, Mr Color provides a wider range of paint colours and finishes than Aqueous Hobby Color, and will dry to a smoother and harder finish. When applying Mr Color paint, 1 to 2 coats are recommended when using paint brushes, and 2 to 3 coats if using an airbrush to spray paint. If airbrushing Mr Color paint, it should be thinned after diluting to a ratio of between 1 (Mr Color) and 1 to 2 Thinner, depending on the degree of paint viscosity required. Gloss levels obtained using gloss coat Mr Color hobby paints can be adjusted by using Flat Base - mix approximately 5 to 10% of C-30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. The percentage of Flat Base used can be adjusted to vary the amount of gloss level obtained.

Mr Color hobby paint is a paint that has long been regarded highly by modelers world wide as a model paint that delivers an outstanding finish. There are a large number of colours and colour types available, which are suitable for painting almost all models. Generally, Mr Color provides a wider range of paint colours and finishes than Aqueous Hobby Color, and will dry to a smoother and harder finish. When applying Mr Color paint, 1 to 2 coats are recommended when using paint brushes, and 2 to 3 coats if using an airbrush to spray paint. If airbrushing Mr Color paint, it should be thinned after diluting to a ratio of between 1 (Mr Color) and 1 to 2 Thinner, depending on the degree of paint viscosity required. Gloss levels obtained using gloss coat Mr Color hobby paints can be adjusted by using Flat Base - mix approximately 5 to 10% of C-30 Flat Base to convert gloss colors to a semi gloss finish, or 10 to 20% for a matt finish. The percentage of Flat Base used can be adjusted to vary the amount of gloss level obtained.

Aqueous Hobby Color is a paint line newly reformulated in 2020 and aimed to be a safer paint with a higher degree of user friendliness. Aqueous Hobby Color paint is water based, which means you will never run out of thinner/reducer – you can use regular water. Tool cleanup is also easier as you can use water. Aqueous Hobby Color paint does contain a mild solvent in it which helps a lot with the adhesion. Leveling capabilities of this paint are high, it provides a glossy finish with a light texture, creating an excellent paint finish.Gloss levels of the Aqueous paint can be adjusted using additives H-40 Flat Base can be mixed with any color and make the paint semi-gloss or even matte/flat. Mix ratio between 5% and 10% is recommended. Mr. Aqueous Hobby Colors are ready for a regular brush application. They are also airbrush friendly; however, it is recommended to reduce it before use with an airbrush. As we mentioned earlier, regular water can be used as a reducer, but for the best result we recommend using Mr. Aqueous Hobby Color Thinner (T-110 or T-111). Up to 150% of the reducer can be added to Aqueous paint for airbrush use. When spraying paints with an airbrush, 2-3 coats are recommended. For regular brush use 1-2 coats is enough. If painting a light color over a darker base surface, more layers of paint may be required.

This is a thinner for water-based hobby colors. If it is difficult to apply with a brush, add a small amount of thinner.For airbrush painting, dilute the paint with a maximum ratio of 1 part thinner to 1 part paint (1:1). This makes it easier to apply as it dries faster than when diluted with water and reduces the repelling phenomenon caused by water. It can also be used to clean tools used with water-based hobby colors, but if it has completely dried and is difficult to remove, use Mr. Tool Cleaner Kai.  Note: This product cannot be used to restore the viscosity of any product that has become too high or completely hardened in the bottle.

Updated Bottle - Now 18ml!!!We have introduced a new formulation that will surprise you with its amazing brushability, excellent opacity and superb matt finish.You will notice that the colors dry quickly, forming a homogeneous and self-leveling layer that respects the smallest detail present in your model. In fact, we recommend applying them on a previously primed surface.Packaging: Model Color is presented in bottles of 18 ml/0.6 fl oz with eyedropper. This packaging prevents the paint from evaporating and drying in the container, so that It can be used in minimal quantities and preserved for a long time.

SMS PL163 Premium Acrylic Lacquer Dark Sea Blue 30ml The Premium range of lacquer model paints are specifically formulated for air brushing straight out of the bottle. With a denser pigment compared to a lot of other model paints, expert results can be gained with minimal effort - just Pour & Spray!