godhand (204)

Spin Mold set for making round flat bottom holes with a diagonal 45° wall. The GodHand Spin Mold 45° Set includes x5 drill bits with diameters of 1.0mm, 1.5mm, 2.0mm, 2.5mm, and 3.0mm. Unlike Spin Blade (without centre pin) (sold separately), it can drill round Molds without pilot holes. Unlike Spin Blade, Spin Mold can NOT use as a chisel tool. A unified 3 mm shaft (with round shank) enables easy replacement without changing the collet chuck of the pin vise body. Compatible with GodHand Power Pin Vise (sold separately) GodHand Micro Power Pin Vise (sold separately) GodHand Short Power Pin Vise Deep Collet Type (sold separately) Portable storage case included

This drill bit is designed specifically for models that have never been seen before. The drill tip is specially designed to be blunt angle for stable cutting.Shallow digging, so it is difficult to penetrate plastic boards, etc.The holes are not easily distorted so you can easily make a circle close to the real circle. When attaching a pin vice, the blade is shorter and the focal length is closer to the object, making it easier to aim and less shaking.Each size is designed with exquisite length for easy interchanging. The shaft size is uniform, so there is no need to change collets.No need to replace them, so you can work fast. Specification Shaft Diameter: 0.1 inch (2.5 mm) Drill Diameter: 0.02 inch (0.5 mm), 0.02 inch (0.6 mm), 0.03 inch (0.7 mm), 0.03 inch (0.8 mm),

This drill bit is designed specifically for models that have never been seen before. The drill tip is specially designed to be blunt angle for stable cutting.Shallow digging, so it is difficult to penetrate plastic boards, etc.The holes are not easily distorted so you can easily make a circle close to the real circle. When attaching a pin vice, the blade is shorter and the focal length is closer to the object, making it easier to aim and less shaking.Each size is designed with exquisite length for easy interchanging. The shaft size is uniform, so there is no need to change collets.No need to replace them, so you can work fast. Specification Shaft Diameter: 0.1 inches (3.0 mm) Drill Diameter: 0.08 inches (2.1 mm), 0.09 inches (2.2 mm), 0.1 inches (2.3 mm), 0.1 inches (2.4 mm), 0.1 inches (2.7 mm), 0.1 inches (2.8 mm), 0.1 inches

Godhand Drill Blade Set of 4 (Blade Width 0.04 - 0.1 inch (1 - 2.5 mm)), Pin Vise 0.1 inch (3 mm) Dedicated Blade Set". The "Blade Type" is now available in the Bit Series. The blade shape is like an arrow feather, so it won't shake even on curved surfaces. Even curved surfaces that are difficult to slip with ordinary drills, it can be carved without slipping. Set of 4 types: Diameter 0.04 inch (1 mm) / 0.06 inch (1.5 mm) / 0.08 inch (2 mm) / 0.1 inch (2.5 mm). *Does Please note that the blade edge may be damaged if used as a chisel. The tip of the blade is very easy to break. Please do not force the blade into place with the edge of the blade.

Hexagonal shaft drill blade designed specifically for model making.You can digging holes without worrying about emptation. Set of 8 hexagonal shafts with 0.2 inch (4 mm) shaft diameters, drill diameters 0.04 inch (1.1 mm), 0.05 inch (1.2 mm), 0.05 inch (1.3 mm), 0.06 inch (1.6 mm), 0.07 inch (1.8 mm), 0.7 inch (1.9 mm). The hexagonal shaft ensures that the connection parts are firmly bite together, so you can work with confidence without worrying about emptying around. The overall length is shorter and closer to the object than a typical drill blade, making it easier to focus and control. The tip of the drill blade is designed with a blunt angle, so it can be dipped shallow and dig holes without penetrating through thin plastic sheets.It is more slowly than the sharp edge of the blade, so it is less likely to shake and the holes are distorted easily. Even the edges of the digged holes are finished. In addition, for drill blades with 0.06 inch (1.5 mm) or more, the blade is added to the tip part. By increasing the penetration power, you can dig with light force without resistance. Simply plug it into the "Quick Power Pin Vise" (sold separately).It is very easy to put on and take off the pin vice and improve your work efficiency.

Hexagonal shaft drill blade designed specifically for model making.You can digging holes without worrying about emptation. Set of 8 hexagonal shafts with 0.16 inch (4 mm) shaft diameters, drill diameters 0.08 inch (2.1 mm), 0.11 inch (2.2 mm), 0.11 inch (2.3 mm), 0.1 inch (2.4 mm), 0.11 inch (2.7 mm), 0.1 inch (2.1 inch (2 The hexagonal shaft ensures that the connection parts are firmly bite together, so you can work with confidence without worrying about emptying around. The overall length is shorter and closer to the object than a typical drill blade, making it easier to focus and control. The tip of the drill blade is designed with a blunt angle, so it can be dipped shallow and dig holes without penetrating through thin plastic sheets.It is more slowly than the sharp edge of the blade, so it is less likely to shake and the holes are distorted easily. Even the edges of the digged holes are finished. In addition, for drill blades with 0.06 inch (1.5 mm) or more, the blade is added to the tip part. By increasing the penetration power, you can dig with light force without resistance. Simply plug it into the "Quick Power Pin Vise" (sold separately).It is very easy to put on and take off the pin vice and improve your work efficiency.

Double-Sided Tape for Mini FF Board, 0.4 inch (10 mm) Wide, Plastic Model Tool The Godhand "Double Sided Tape for Mini FF Boards" is 0.4 inch (10 mm) wide. This is a special double-sided tape perfect for "Mini FF Board Stainless Steel 0.4 inch (10 mm) width (GH-FFM-10). Specially designed for different adhesive strength on the front and back of the tape. It also goes well with the "Flex Cloth File Set (GH-NY4)" which is easy to peel off with regular double-sided tape. It has a weak adhesive on one side that makes it easy to remove from the board when you are replacing it.  Specification Dedicated double-sided tape perfect for "Mini FF Board Stainless Steel 0.4 inch (10 mm) wide (GH-FFM-10)  The tape has a special design with different adhesive strength on the front and back for easy removal  Material: Adhesive film  Size: Width: 0.4 inch (10 mm) / 98.8 ft (  Country of Manufacture: Japan

Double-Sided Tape for FF Board, 0.6 inches (15 mm) Wide, Plastic Model Tool Godhand "FF Board Acrylic Double-Sided Tape 0.6 inch (15 mm) wide" This is a special double-sided tape perfect for "FF Board Acrylic 0.6 inch (15 mm) width (GH-FFA-15). Specially designed for different adhesive strength on the front and back of the tape. It also goes well with the "Flex Cloth File Set (GH-NY4)" which is easy to peel off with regular double-sided tape. Specification FF Board Acrylic 5 Piece Set (GH-FFA-15) Dedicated Double-Sided Tape  The tape has a special design with different adhesive strength on the front and back for easy removal  Material: Adhesive film  Size: Width: 0.6 inch (15 mm) / 98.8 ft (  Country of Manufacture: Japan

God Hand GH-DST-20 Strong double-sided tape for Pla-Plate Specification Dedicated double-sided tape perfect for "Mini FF Board Stainless Steel 0.2 inch (6 mm) wide (GH-FFM-6) Strong adhesive on both sides that can be firmly attached even in narrow widths Material: Adhesive film Size: Width: 0.2 inch (6 mm) / 98.8 ft Country of Manufacture: Japan

Brushwork Deluxe Flat Brush M The brushes are suitable for painting wide surfaces and large-scale models. The brush tips are quite big, so they retain paint and water very well. It's suitable for painting small parts of wide surfaces in different colors. Each brush is hand-made by Japanese brush craftspersons who specialize in synthetic bristles. Animal hair brushes tend to become damaged, torn, and dry when soaked in solvents, but Brushwork PRO’s PBT bristles are solvent-resistant and less prone to damage. The bond that holds the brush tip in place is also solvent-resistant, ensuring a long-lasting good brush tip. The brush tip is more flexible than general chemical fiber brushes due to the firmness adjusted for easy brush painting on models. An assorted range of brush tip shapes for use in different painting situations. Short brush tip has a lower water supply for the paint, causing the paint to dry quickly. This is why Brushwork PRO has designed the brush tip length to achieve ease of painting and paint absorbency. Thanks to the special processing PBT bristles, bent bristles become straight again with hot water at 90℃. How to fix a brush with bristles bent out Remove any dirt from the brush before soaking it in hot water. *Please be careful of burns when using hot water. Fill a heat-resistant container with hot water at 90℃, and soak the bent brush tips for about 10 seconds. Use the sides of the container to straighten out any bent bristles. Pull the brush up along the side to keep it straight. Check the bottom of the brush is straight and leave it to dry. *For some bristles with a limited lifespan in use, it may not work.*Note that if the water gets cold during the process, it may not work.

Brushwork Deluxe Flat Brush S The brushes are suitable for painting wide surfaces and large-scale models. The brush tips are quite big, so they retain paint and water very well. It's suitable for painting small parts of wide surfaces in different colors. Each brush is hand-made by Japanese brush craftspersons who specialize in synthetic bristles. Animal hair brushes tend to become damaged, torn, and dry when soaked in solvents, but Brushwork PRO’s PBT bristles are solvent-resistant and less prone to damage. The bond that holds the brush tip in place is also solvent-resistant, ensuring a long-lasting good brush tip. The brush tip is more flexible than general chemical fiber brushes due to the firmness adjusted for easy brush painting on models. An assorted range of brush tip shapes for use in different painting situations. Short brush tip has a lower water supply for the paint, causing the paint to dry quickly. This is why Brushwork PRO has designed the brush tip length to achieve ease of painting and paint absorbency. Thanks to the special processing PBT bristles, bent bristles become straight again with hot water at 90℃. How to fix a brush with bristles bent out Remove any dirt from the brush before soaking it in hot water. *Please be careful of burns when using hot water. Fill a heat-resistant container with hot water at 90℃, and soak the bent brush tips for about 10 seconds. Use the sides of the container to straighten out any bent bristles. Pull the brush up along the side to keep it straight. Check the bottom of the brush is straight and leave it to dry. *For some bristles with a limited lifespan in use, it may not work.*Note that if the water gets cold during the process, it may not work.

Brushwork Deluxe Pointed Round M The brushes are suitable for painting wide surfaces and large-scale models. The brush tips are quite big, so they retain paint and water very well. It's suitable for painting small parts of wide surfaces in different colors. Each brush is hand-made by Japanese brush craftspersons who specialize in synthetic bristles. Animal hair brushes tend to become damaged, torn, and dry when soaked in solvents, but Brushwork PRO’s PBT bristles are solvent-resistant and less prone to damage. The bond that holds the brush tip in place is also solvent-resistant, ensuring a long-lasting good brush tip. The brush tip is more flexible than general chemical fiber brushes due to the firmness adjusted for easy brush painting on models. An assorted range of brush tip shapes for use in different painting situations. Short brush tip has a lower water supply for the paint, causing the paint to dry quickly. This is why Brushwork PRO has designed the brush tip length to achieve ease of painting and paint absorbency. Thanks to the special processing PBT bristles, bent bristles become straight again with hot water at 90℃. How to fix a brush with bristles bent out Remove any dirt from the brush before soaking it in hot water. *Please be careful of burns when using hot water. Fill a heat-resistant container with hot water at 90℃, and soak the bent brush tips for about 10 seconds. Use the sides of the container to straighten out any bent bristles. Pull the brush up along the side to keep it straight. Check the bottom of the brush is straight and leave it to dry. *For some bristles with a limited lifespan in use, it may not work.*Note that if the water gets cold during the process, it may not work.

Brushwork Deluxe Point Brush M The brushes are suitable for painting wide surfaces and large-scale models. The brush tips are quite big, so they retain paint and water very well.It's suitable for precise drawing of narrow lines or faces of large-scale models. Each brush is hand-made by Japanese brush craftspersons who specialize in synthetic bristles. Animal hair brushes tend to become damaged, torn, and dry when soaked in solvents, but Brushwork PRO’s PBT bristles are solvent-resistant and less prone to damage. The bond that holds the brush tip in place is also solvent-resistant, ensuring a long-lasting good brush tip. The brush tip is more flexible than general chemical fiber brushes due to the firmness adjusted for easy brush painting on models. An assorted range of brush tip shapes for use in different painting situations. Short brush tip has a lower water supply for the paint, causing the paint to dry quickly. This is why Brushwork PRO has designed the brush tip length to achieve ease of painting and paint absorbency. Thanks to the special processing PBT bristles, bent bristles become straight again with hot water at 90℃. How to fix a brush with bristles bent out Remove any dirt from the brush before soaking it in hot water. *Please be careful of burns when using hot water. Fill a heat-resistant container with hot water at 90℃, and soak the bent brush tips for about 10 seconds. Use the sides of the container to straighten out any bent bristles. Pull the brush up along the side to keep it straight. Check the bottom of the brush is straight and leave it to dry. *For some bristles with a limited lifespan in use, it may not work.*Note that if the water gets cold during the process, it may not work.

Brushwork Deluxe Angular M The brushes are suitable for painting wide surfaces and large-scale models. The brush tips are quite big, so they retain paint and water very well. It's suitable for painting small parts of wide surfaces in different colors. Each brush is hand-made by Japanese brush craftspersons who specialize in synthetic bristles. Animal hair brushes tend to become damaged, torn, and dry when soaked in solvents, but Brushwork PRO’s PBT bristles are solvent-resistant and less prone to damage. The bond that holds the brush tip in place is also solvent-resistant, ensuring a long-lasting good brush tip. The brush tip is more flexible than general chemical fiber brushes due to the firmness adjusted for easy brush painting on models. An assorted range of brush tip shapes for use in different painting situations. Short brush tip has a lower water supply for the paint, causing the paint to dry quickly. This is why Brushwork PRO has designed the brush tip length to achieve ease of painting and paint absorbency. Thanks to the special processing PBT bristles, bent bristles become straight again with hot water at 90℃. How to fix a brush with bristles bent out Remove any dirt from the brush before soaking it in hot water. *Please be careful of burns when using hot water. Fill a heat-resistant container with hot water at 90℃, and soak the bent brush tips for about 10 seconds. Use the sides of the container to straighten out any bent bristles. Pull the brush up along the side to keep it straight. Check the bottom of the brush is straight and leave it to dry. *For some bristles with a limited lifespan in use, it may not work.*Note that if the water gets cold during the process, it may not work.